View TM21R-5B-4848D-LP_482562.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NEW
Modular Jack Connectors for High-Speed LAN Transmission
TM21R Series
Built-in Optical Indicators
LED Optical indicator Optical pipe
sFeatures
1. Supports High-Speed LAN Transmission
Meets requirements of TIA/EIA-568-B data wiring standard. Single port configuration meeting CAT5e and multiple port configuration meeting CAT5 transmission performance. As such, these products fully support Gigabit Ethernet (1000BASE-T) and Fast Ethernet (100BASE-TX) highspeed LAN transmission.
Housing
Optical indicator area
Space saving Optical indicator
2. Built-in Optical Indicators
Optical indicators are integral part of the connectors saving space on customer's board. Compared with LED type indicators, they do not emit any electrical noise.
3. EMI protection
Metal shield covers the outer surfaces of the connectors assuring complete protection against electromagnetic interference. Built-in multiple shield and ground contacts assure reliable connection with the mounting panel as well as with the mating connector.
One additional TM21 multi-port jack can be mounted in the space previously occupied by LEDs.
4. FCC Standards
Meets requirements of FCC Title 47, Part 68, Subpart F.
sApplications
Telecom Hubs, Routers, Bridges and ATM Transmission Equipment, Ethernet Switches and Networking Equipment, Test and Measurement Equipment, Medical Diagnostic Equipment.
Built-in LED type (Possibility of electromagnetic noise emission and interference.)
Built-in Optical pipe type (No electromagnetic noise emission.)
2002.11
1
sProduct Specifications
Current rating Ratings Voltage rating 125 V AC 1A Operating temperature range-25c to +80c (Note)
Item
01.Insulation resistance 100 M ohms min
Specification
100 V DC 500 V AC / one minute
Conditions
02.Dielectric Withstanding Voltage No flashover or insulation breakdown (between adjacent contacts) 03.Withstanding voltage No flashover or insulation breakdown (between contact and shield) 04.Contact resistance 05.Vibration 230 m ohms max. No electrical discontinuity of 5 ms or more Contact resistance: 250m ohms max. No electrical discontinuity of 5ms or more Contact resistance: 250m ohms max. Contact resistance: 250m ohms max.
1500 V AC / one minute 100mA DC Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours / 3 axis Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis 200 cycles (Temperature: -55c/+5c to +35c/+85c/+5c to +35c Duration: 30 / 5 / 30 / 5 (Minutes) 5 cycles
06.Shock 07.Durability (mating/unmating)
08.Temperature cycle
Contact resistance: 250 m ohms max. Insulation resistance: 100 M ohms min. Contact resistance: 250 m ohms max. Insulation resistance: 1 M ohms min. (High humidity) Insulation resistance: 10 M ohms min. (Dry state) Contact resistance: 250 m ohms max.
09.Humidity
500 hours at temperature of 40c and humidity of 90% to 95%
10.Salt Spray
Exposed to density 5% salt water for 48 hours
Note :Includes temperature rise caused by current flow.
sMaterials
Part Insulator Contact Optical pipe Shield Material PBT Copper alloy Poly carbonate Copper alloy Finish Color: Black Contact area: Gold plating Termination area: Solder plating Color: Clear Tin plating Remarks UL94V-0 -------------------
sOrdering information
qJacks
TM21 R - 5 A - 32 32 D - LP
1 2 3 4 5 6 7 8
q Series Name w Connector type e Jack type number r Jack performance level code
TM21 R : Jack 5 : PCB Right-angle through hole type A : CAT5 (Single row, multi-port) B : CAT5 (Double row, multi port) C : Supports CAT5e (Single port) t Jack opening code 8 : 8 contacts 32 : 8 contacts /4 ports 48 : 8 contact/6 ports y Number of inserted contacts 8 : 8 contact 32 : 8 contact inserted in 4 ports=32 contacts 48 : 8 contact inserted in 6 ports=48 contacts u Number of rows Blank: Single row D: Double row i Optical pipe LP: With optical pipe inserted Blank: Without optical pipe
2
sModular Jack Connectors Supporting CAT5e
qSingle Port With Built-in Optical Pipe
16 Contact No.8 Contact No.1 0.8 21 (5.5)
13.75
13.4
3
3.6
0.8
(2.8) 1 3.05 10.25 6.35 13.05 24 0.35 2.54
0.45 11.43 15.75 0.8
0.25
0.8
Contact No.8 11.9
Part Number TM21R-5C-88-LP
CL No. 222-2892-0
qSingle Port Without Optical Pipe
21 16 Contact No.8 Contact No.1 0.8 (5.5)
13.75
13.4
3
3.6
0.8
(2.8) 1 3.05 10.25 6.35 13.05 24 0.35 2.54
0.45 11.43 15.75 0.8
0.25
0.8
Contact No.8 11.9
Part Number TM21R-5C-88
CL No. 222-2893-2
TM21R-5C 1 PC
Contact No.7
(5.5)
Contact No.1 Contact No.2
(5.5)
1.7
TM21R-5C 1 PC
Contact No.7
(5.5)
Contact No.1 Contact No.2
(5.5)
1.7
3
BRecommended PCB mounting patterns
qWith Built-in Optical Pipe
11.9 8.89 6.35 3.81 1.27 LED location area LED light emission area No ground traces Contact No. 3MIN
8 7 6 5 4 3 1 2
qWithout Optical Pipe
8.89 6.35 3.81 1.27 Contact No.
8 5 6 4 3 1 2
8-O 1
2.54
3
8O1 .2 O3 2-
13.05
6.35
6.35
2-
O3
3MIN
7
6.75
6.75
6.75
3MIN
3.05
2O1 .6
3.05
11.43 15.75
Printed board edge Connector front edge 11.43MIN No conductive traces
2
2O1
.6
11.43 15.75
Printed board edge Connector front edge 11.43MIN No conductive traces
2
*Recommendations for PCB Design
1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Area indicated should be free of ground traces. 4 Recommended board thickness: 1.6mm. 5 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification.
1
PCB mounting pattern
Other Series 7531 TM21R Series 8532
8642
6.75
3MIN
.2
2.54
1
1
No ground traces
3
7641
5
Suggested LEDs
LED light emitting center
2.7MAX
3.2MAX
1.5MAX
BPanel Cutout
qFor Both Types, With and Without Built-in Optical Pipe
(33) 0.6MIN 4.5MIN TM21P--88P Lock lever TM21R--5C--88--LP 4.5
+1 -2 1
PCB mounting surface
0.15
14.1
Panel side 16.4
1
Connector front surface
1
0 2.8 -0.8
6.75 10.25
*Recommendations for Panel Design
1 The shield contacts should connect with the panel cut-out on all sides.
4
sModular Receptacles Supporting CAT5
qSingle row/ multiple ports, with Built-in Optical Pipe
59.18 41.91 13.97 1 Contact No.1 Contact No.8 25.9 (6)
15.3
1.7 (3.5) 0.35 1.4 2.5 10.25 15.525 8.34 SML-010 Series 10.9 1.6
15.4
Part Number TM21R-5A-3232-LP
CL No. 222-2873-5
1
0.45 Contact No.2 0.25 Contact No.1 53.81 58.93
Contact No.7 Contact No.8 1
(6)
3.6
11.9
BRecommended PCB mounting patterns
LED Mount Area Dimensions
58.93 41.91 4-O2 LED location area LED light emission area
4
CL-220 Series 13.97 8.89 6.35 3.81 1.27 5.8 1.2 11.9
4
1.4
12.7
1.45
1.3
32-O1 15.525
5.8 8.34
12.7
1
(6)
0.75
3
12.7 8.34
8.34
1467 2358
SML-020 Series 10.4 2.5 2.7 0.6
6MAX
3MIN
Contact No.
1
4-O2 2-O3.2
No conductive traces 53.81
2
Printed board edge Connector front edge 12.7
*Recommendations for PCB Design
1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Recommended board thickness: 1.6mm. 4 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 4 Suggested LEDs
Series Name CL-220 SML-010 SML-020 Manufacturer Citizen Electronics Co., Ltd. Rohm Co., LTD Rohm Co., LTD
1 PCB mounting pattern
2 4 6 8 1 4 6 7
1
4.4
3
1
5
7
12.7
1.5
2
3
5
8
15.4
5
BRecommended Panel Cutout
0.15
4.5MIN 13.97 41.91 Panels Side 59.6
1
(34) TM21P-- 88P Connector front surface
5 - 2.5
+1
1
Lock lever 3.5
0 -1
6 MAX
10.25
*Recommendations for Panel Design
1 The shield contacts should connect with the panel cut-out on all sides.
6
0.4MIN Shield spring contact
15.8
PCB mounting surface
qDouble row / multiple port, with Built-in Optical Pipe
1
A B 13.97 Contact No.8
32.5 Upper row Contact No.1 27.9 (6)
28
TM21R-5B-3232D-LP
0.45 Contact No.1 0.25 C D (6) 1 Lower row connectors contacts 0.75 3.6 3 Contact No.8 Lower row (6) 1 (3.5) 1.4 2.5 10.25 8.34 5.8 14.94 22.125
0.35
12.4
14.94
1 PBT
2358 1467 7641 8532
TM21R-5B-4848D-LP
11.9
Upper row connectors contacts 7.7
Part Number TM21R-5B-3232D-LP TM21R-5B-4848D-LP
CL No. 222-2879-1 222-2885-4
A 59.18 87.12
B 41.91 69.85
C 53.81 81.75
D 58.93 86.87
BRecommended PCB mounting pattern
A B
4
Upper row LED mount position Lower row LED mount position
11.9 7.7 LED light emission area E- O2
13.97 8.89 6.35 3.81 1.27 Upper row contact hole Lower row contact hole
4
1.2 1.4 1.3
19.3
14.94
6 MAX
3 MIN
2.5
4- O2 2- O3.2
1
Contact No.
No conductive traces C
2
Printed board edge Connector front edge
Part Number TM21R-5B-3232D-LP TM21R-5B-4848D-LP
CL No. 222-2879-1 222-2885-4
A 58.93 86.87
B 41.91 69.85
C 53.81 81.75
D 64 96
5.8
8.34
1467 2358
E 4 6
*Recommendations for PCB Design
1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Recommended board thickness: 1.6mm. 4 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification.
1 PCB mounting pattern
Other Series 7 8 2 1 3 6 4 5 5 4 6 7 3 2 8 2 1 7 1 3 TM21R Series 8 6 4 5 5 4 6 8 3 1 7 2
4 Suggested LEDs
Series Name CL-220 Manufacturer Citizen Electronics Co., Ltd.
12.4
D- O1
14.94
8532 7641
22.125
19.3
1.7
28
7
BPanes Cutout
1
Shield spring contact spring
PCB mounting surface
0.15
4.5MIN 13.97 Panel Side A B
Part Number TM21R-5B-3232D-LP TM21R-5B-4848D-LP
CL No. 222-2879-1 222-2885-4
A 41.91 69.85
B 59.60 87.54
(34)
5
+1 -2.5
1
TM21P -- 88P
Lock lever
TM21R -- 5B -- * * * * D -- LP
1
Connector front surface
6 MAX
1
0 3.5 -1
10.25
*Recommendations for Panel Design
1 The shield contacts should connect with the panel cut-out on all sides.
8
0.4 MIN
28.4
BTechnical Documentation CAT5e Transmission Characteristics Data
Representative values of the various transmission characteristics data for fully mated receptacle (TM21R-5C-88-LP) and plug (TM21P-88P). All plugs in the TM21R-5C Series that were manufactured based on the De-embedded method of the TIA/EIA-568-B.2 standard and meet performance requirements of CAT5e single transmission. Note:These data are for the listed connector combination. Inquire with your Hirose Electric account representative about other combinations.
qSignal Attenuation
0.5 Attenuation(dB) 0.4 0.3 0.2 0.1 0 0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec
qNear-End Crosstalk (NEXT) Data
120 100 NEXT(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz) 1,2-3,6 3,6-7,8 1,2-4,5 4,5-7,8 1,2-7,8 CAT5e Spec 3,6-4,5
qReturn Loss
80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100
Return Loss(dB)
Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec
9
qFar-End Crosstalk (FEXT)
120 100 FEXT(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz) 1,2-3,6 3,6-1,2 4,5-1,2 7,8-1,2 CAT5e Spec 1,2-4,5 3,6-4,5 4,5-3,6 7,8-3,6 1,2-7,8 3,6-7,8 4,5-7,8 7,8-4,5
qPropagation Delay
3 2.5 Delay(ns) 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec
qPropagation Delay (Delay Skew)
1.4 1.2 Delay Skew(ns) 1 0.8 0.6 0.4 0.2 0 0 10 20 30 40 50 60 70 80 90 100
Frequency(MHz) CAT5e Spec
10
BReference Documentation
qCAT6 Certification Received
Only the high quality plugs in the TM21R-5C Series (based on the De-embedded method of the TIA/EIA-568-B.2 standard) clear CAT6 single transmission performance. A certificate was issued by the GHMT, independent European testing company.
Certificate of Acceptance
11
USA: HIROSE ELECTRIC U.S.A., INC. 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : 1 805 522 7958 Fax : 1 805 522 3217 http://www.hirose.com
GERMANY: EUROPE BRANCH: HIROSE ELECTRIC GmbH HIROSE ELECTRIC CO., LTD. First Class Building 4F, Beechavenue 46.1119PV Zeppelinstrasse 42 D-73760 Ostfildern Kemnat Phone : 49 711 4560021 Schiphol-Rijk, The Netherlands Fax : 49 711 4560729 Phone : 31 20 6557 460 http://www.hirose.de Fax : 31 20 6557 469 http://hiroseeurope.com CHINA: HIROSE ELECTRIC CO., LTD. 10F,No.06, Shanghai Times Square office Tower, 93. Huai Hai Zhong Road, Luwan Shanghai Phone : 86 21 6391 0011 Fax : 86 21 6391 0101 SINGAPORE: HIROSE ELECTRIC CO., LTD. 10 Anson Road #34-13 International Plaza 079903 Phone : 65 6324 6113 Fax : 65 6324 6123
UNITED KINGDOM: KOREA: HIROSE ELECTRIC UK LTD. HIROSE KOREA CO., LTD. Crownhill Business Centre 22 Vincent Avenue (#2NA311,Shihwa Industrial Complex), Crownhill, Milton Keynes MK8 OAB 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone : 44 1908 305400 Phone : 82 31 496 7000,7124 Fax : 44 1908 305401 Fax : 82 31 496 7101 http://www.hirose.co.uk http://www.hirose.co.kr HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha Tsui East, Kowloon Phone : 852 2803 5338 Fax : 852 2591 6560 TAIWAN: HIROSE ELECTRIC CO., LTD. No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei Phone : 886 2 2557 7351,7352 Fax : 886 2 2552 9851
Crea tiv
to World E inks le eL
(R)
12
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of product improvements.
s onic ctr
HIROSE ELECTRIC CO., LTD.
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933

▲Up To Search▲

Price & Availability of TM21R-5B-4848D-LP

	To Download TM21R-5B-4848D-LP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .